例句與造句

1. Resistance strain gauge rolling force measuring instrument
   電阻應變式軋制力測量?jī)x
2. Adaptive modification of the rolling force prediction
   軋制力預報的自適應修正
3. Application of computer system for monitoring mill rolling force
   軋機壓力監測系統的應用
4. Magnetoelastic rolling force measuring instrument
   磁彈性式軋制力測量?jī)x
5. Distributed rolling force signal acquisition and fault diagnostic system based on field bus
   基于現場總線分布式軋制力信號采集及故障監測系統
6. It's difficult to find roll force in a sentence. 用roll force造句挺難的
7. Abstract : the artificial intelligence method to setup and control rolling force is researched
   文摘:研究了軋制力設定控制的人工智能實現方法。
8. The application of the attached type ergometric sensor for monitoring the rolling force of the heavy plate mill
   附著式測力傳感器在大型軋機軋制力監測中的應用
9. There are two kinds of method to measure the rolling force : stress measure and sensor measure
   機械工程中測量軋制力的方法有兩種：應力測量法和傳感器測量法。
10. Sea wave high , pitching force , rolling force and rearing torque simulation algorithms are put forward
    給出了隨機海浪波高、橫蕩力、橫搖力矩、艏搖力矩的仿真算法。
11. Simulated rolling force , temperature value and microstructure are of good agreement with the measured results
    模擬得到的軋制力能參數、溫度、組織分布與實測數據基本一致。
12. The comparisons among three kinds of calculation methods for rolling force in cold strip rollingwere carried out , a new kind of real time counting for the deform of strip was briefed
    介紹了三種常用的冷軋帶鋼軋制力計算方法間的比較及一種新帶鋼變形的實時計算方法。
13. In order to improve the precision of the model , a new method using self adaption and artificial neural networks to predict rolling force was developed
    為了提高中厚板軋機軋制力的預報精度，采用軋制力模型自適應與人工神經元網絡相結合的方法進行中厚板軋制力的在線預報。
14. In this paper the results of application of this software to analyze q235 steel , were introduced the results showed , that the rolling force and temperature are in good agreement with the measured , the predicted mechanical properties are near to measured
    經過修正的軋制力和溫度的預測值與在線系統的實測值基本吻合，力學性能的預測值與實測值的誤差不大。
15. In order to study the deformation and rolling force during finishing of steel flats , an analytical model based on elastic plastic finite element method was established to simulate systematically the whole finishing process
    摘要為研究扁鋼精整過程中的變形和軋制力的變化規律，利用彈塑性有限元方法建立了扁鋼精整過程的分析模型，系統地模擬了扁鋼精整的全過程。
16. The results show that the simulated deformation and rolling force of steel flats during finishing are in good agreement with the actual ones , offering reference data for the calculation of finishing parameters
    仿真結果表明：利用彈塑性有限元法模擬得到的扁鋼精整后變形與實際變形基本吻合；且仿真所得的軋制力大小與物理測得的現場數據吻合較好，為精確計算各精整參數提供了參考數據。
更多例句：  下一頁